Earthquakes are common geological disasters, and slopes under seismic loading can trigger coseismic landslides, while also becoming unstable due to accumulated damage caused by the seismic activity. Reinforced soil slopes are widely used as seismic-resistant geotechnical systems. However, traditional geosynthetics cannot sense internal damage in reinforced soil systems, and existing in-situ distributed monitoring technologies are not suitable for seismic conditions, thus limiting accurate post-earthquake stability assessments of slopes. This study presents, for the first time, the use of a batch molding process to fabricate self-sensing piezoelectric geogrids (SPGG) for distributed monitoring of soil behavior under seismic conditions. The SPGG's reinforcement and damage sensing abilities were verified through model experiments. Results show that SPGG significantly enhances soil seismic resistance and can detect soil failure locations through voltage distortions. Additionally, the tensile deformation of the reinforcement material can be quantified with sub-centimeter precision by tracking impedance changes, enabling high-precision distributed monitoring of reinforced soil under seismic conditions. Notably, when integrated with wireless transmission technology, the SPGG-based monitoring system offers a promising solution for real-time monitoring and early warning in road infrastructure, where rapid detection and response to seismic hazards are critical for mitigating catastrophic outcomes.

To investigate the effect of interface temperature on the soil-reinforcement interaction mechanism, a series of pullout tests were conducted considering different types of reinforcement (geogrid and non-woven geotextile), backfill (dry sand, wet sand, and clay), and six interface temperatures. The test results indicate that at interface temperatures of 0 degrees C and above, reinforcement failure didn't occur during the pullout tests, whereas it predominantly occurred at subzero temperatures. Besides, the pullout resistance for the same soil-reinforcement interface gradually decreased as the interface temperature rose. At a given positive interface temperature, the pullout resistance between wet sand and reinforcement was significantly higher than that of the clayreinforcement interface but lower than that of the dry sand-reinforcement interface. Compared with geotextile reinforcements, geogrids were more difficult to pull out under the same interface temperature and backfill conditions. In addition, the lag effect in the transfer of tensile forces within the reinforcements was significantly influenced by the type of soil-reinforcement interface and the interface temperature. Finally, the progressive deformation mechanism along the reinforcement length at different interface temperatures was analyzed based on the strain distribution in the reinforcement.

In performance-based design, it is crucial to understand deformation characteristics of geocell layers in soil under footing loads. To explore this, a series of laboratory loading tests were carried out to investigate the influence of varying parameters on the strain levels within the geocell layer in a sandy soil under axial strip footing loading. The results were analyzed in terms of maximum strain levels, strain variation along the geocell layer and the correlation between horizontal and vertical strains. In this study, the maximum observed strain levels for geocellreinforced strip footing systems reached 2.3 % for horizontal (tensile) strain and 1.4 % for vertical (compressive) strain. Furthermore, most strain levels were concentrated within a distance of 1.5 times the footing width from the axis of strip footing. In geocell-reinforced footing systems, the interaction between horizontal and vertical strains becomes a key factor, with the ratio of horizontal to vertical cell wall strains ranging approximately from 1 to 2.5. The outcomes of this study are expected to contribute to the practical applications of geocell-reinforced footing systems.

Tiered geosynthetic-reinforced soil (GRS) walls in transportation engineering are often applied in high-retaining soil structures and are typically subjected to traffic cyclic loading. However, there has been limited research on the dynamic performance of tiered GRS walls. Three reduced-scale model walls were conducted to investigate the dynamic performances of two-tiered GRS walls with different strip footing locations (d/H) under cyclic loading. The test results demonstrated that cyclic loading parameters such as average load P0 and load amplitude PA have a significant effect on the dynamic performance of the tiered walls. However, the change in loading frequency f has a minor effect on the settlement and lateral deformation when the GRS wall reaches a relatively stable state. Under the same P0 and PA, the measured maximum additional vertical stress Delta sigma v,max decreases with the increase of frequency f, whereas minimum additional vertical stress Delta sigma v,min increases. The stress distribution profile along the horizontal direction at the lower-tier wall crest is related to the strip footing location. The bearing capacity of the GRS wall increases and then decreases with increasing d/H within the reinforced zone of the upper-tier wall. The variation magnitude and distribution profile of the lateral deformations are influenced by the d/H and cyclic loading levels, especially for the upper-tier wall. When the strip footing remains in the reinforced zone of the upper-tier wall, potential slip surfaces go deeper as it moves away from the wall face. Finally, a power relationship between the calculated factor of safety and the maximum lateral deformation monitored from model tests for the two-tiered GRS walls under cyclic loading is established.

A series of finite element analyses, conducted on the basis of modified triaxial tests incorporating radial drainage, were carried out to investigate the lateral deformation and stress state characteristics of prefabricated vertical drain (PVD) unit cells under vacuum preloading. The analyses revealed that the inward horizontal strain of the unit cell increases approximately linearly with the vacuum pressure (Pv) but decreases non-linearly with an increase in the initial vertical effective stress (sigma ' v0). The variations in the effective stress ratio, corresponding to the median excess pore water pressure during vacuum preloading of the PVD unit cell, were elucidated in relation to the Pv and sigma ' v0 using the simulation data. Relationships were established between the normalized horizontal strain and normalized effective stress ratio, as well as between the normalized stress ratio and a composite index parameter that quantitatively captures the effects of vacuum pressure, initial effective stress, and subsoil consolidation characteristics. These relationships facilitate the prediction of lateral deformation in PVD-improved grounds subjected to vacuum preloading, utilizing fundamental preloading conditions and soil properties. Finally, the proposed methodology was applied to analyze two field case histories, and its validity was confirmed by the close correspondence between the predicted and measured lateral deformation.

Geocells are three-dimensional, interconnected cellular geosynthetics widely used to enhance the overall strength of soils. Their foldable structure can cause variations in pocket shape during installation, depending on the extent of extension. Understanding the impact of these shape variations is essential for optimizing reinforcement efficiency and reducing the associated geocell application costs. The aspect ratio, defined as the ratio of the cell's transverse (welded) axis to the longitudinal (wall summit) axis, is proposed to evaluate the degree of extension of the most commonly utilized honeycomb-shaped geocell. A coupled continuum-discontinuum numerical method was employed to investigate the behavior of honeycomb-shaped geocell reinforced soils across various aspect ratios under confined compressive loading. The simulation results indicate that a geocell with an aspect ratio of 1.0 exhibits optimal reinforcement efficiency, and whereas reinforcement efficiency decreases as the aspect ratio deviates from 1.0 causing pocket geometries to flatten. The superior performance of rounded geocells is attributed to their enhanced ability to promote load-bearing in strong contact subnetworks. This results in denser packing structures, higher contact force anisotropy from a microscopic perspective, and greater confinement capacity against deformation from a macroscopic perspective.

The soilbags reinforcement has been widely used for soft soil foundation improvement due to its high compressive strength and deformation modulus considering the time limit of many projects and the characteristics of the reclaimed soil. However, despite the strength and deformation properties of soilbags reinforcement, the drainage characteristics of soilbags reinforcement is a crucial factor that creates a large challenge to foundation improvement for soft soil. Thus, this study developed a four-staged surcharge preloading on soilbags-reinforced soft soil foundation and focused on its drainage consolidation effectiveness. The contrasting laboratory tests were performed in four identical experimental boxes with clayey soil from the Nanjing, China. Four-staged preloading were applied on the soilbags-reinforced testing model, respectively, the data of the settlement and water discharge during the test are monitored, and after the tests, the water content and shear strength at different positions are measured. And three contrasting tests considering the possible drainage channels of soilbags reinforcement were also conducted. The results show that the consolidation effect is achieved with the soilbags reinforcement in terms of the settlement, pore water pressure, water content and shear strength after consolidation.

Pile-supported embankments are one of the most commonly used techniques for ground improvement in soft soil areas. Existing studies have mainly focused on embankments supported by end-bearing piles under static loading, with limited research on floating pile-supported embankments under cyclic traffic loading. In this study, model tests for unreinforced floating, unreinforced end-bearing, geosynthetic reinforced floating, and geosynthetic reinforced end-bearing pile-supported embankments were conducted. Cyclic traffic loading was simulated using a three-stage semi-sinusoidal cyclic loading. Comparative analyses and discussions are performed under floating and end-bearing conditions to investigate the influence of floating piles on the soil arching evolution and membrane effect under cyclic loading. The results indicate that floating piles result in earlier stabilization of surface settlement. There is less arching and membrane effect induced by floating piles, and the arching does not continue to degrade under cyclic loading. Less membrane effect in floating pile-supported embankments results in less geosynthetic and pile strain. The degree of membrane effect in floating pile-supported embankment largely depends on the pile-end condition.

In this study, a flexible vertical graphene (VG) strain sensor was developed for monitoring geogrids deformation. The VG material was fabricated using radio frequency plasma-enhanced chemical vapor deposition, followed by spin-coating a polydimethylsiloxane (PDMS) solution for film curing, resulting in a flexible sensor within a PDMS substrate. The VG sensor was integrated with a wireless Bluetooth data acquisition system for automated and remote strain measurement. The stability performance of VG sensors was examined and effectively improved through cyclic loading tests in the laboratory. The drift ratio of electrical resistance before cyclic loading tests is 37.01%, which is reduced to only 0.5% after cyclic loading tests. Calibration tests show that the maximum measurement resolution and maximum measurement range of VG sensors is 0.7 micro-strain and 40000 micro-strain, respectively, indicating that VG sensors are highly effective for both high-strain resolution identification and large-strain measurement. Pullout tests demonstrate an average error of 5.67% between VG sensors and fiber Bragg grating sensors, suggesting that VG sensors are a promising alternative for large strain, wireless, and long-term geogrid monitoring.

Expanded Polystyrene (EPS) granular lightweight soil (ELS) is an eco-friendly material made of EPS particles, cement, soil, and water. This study investigates the modification of ELS using a silane coupling agent (SCA) solution to improve its performance. Various tests were performed, including flowability, dry shrinkage, unconfined compressive strength (UCS), triaxial, hollow torsional shear, and scanning electron microscopy (SEM) analysis, to evaluate the physical and mechanical properties at different SCA concentrations. The results show that the optimal SCA concentration was 6%, improving flowability by 13% and increasing dry shrinkage weight by 4%. The UCS increased with SCA concentration, reaching 266 and 361 kPa after 7 and 28 days, respectively, at 6% SCA. Triaxial and shear tests indicated improved shear strength, with the maximum shear strength reaching 500 kPa, internal friction angle rising by 4%, and cohesion reaching 114 kPa at 6% SCA. Hollow torsion shear tests showed that 6% SCA enhanced stiffness and resistance to deformation, while reducing the non-coaxial effect. SEM analysis revealed that SCA strengthened the bond between EPS particles and the cement matrix, improving the interfacial bond. This study highlights the potential of modified ELS for sustainable construction.