The cyclic behavior of clay significantly influences the dynamic response of offshore wind turbines (OWTs). This study presents a practical bounding surface model capable of describing both cyclic shakedown and cyclic degradation. The model is characterized by a simple theoretical framework and a limited number of parameters, and it has been numerically implemented in ABAQUS through a user-defined material (UMAT) subroutine. The yield surface remains fixed at the origin with isotropic hardening, while a movable projection center is introduced to capture cyclic hysteresis behavior. Cumulative plastic deviatoric strain is integrated into the plastic modulus to represent cyclic accumulation. Validation against undrained cyclic tests on three types of clay demonstrates its capability in reproducing stress-strain hysteresis, cyclic shakedown, and cyclic degradation. Additionally, its effectiveness in solving finite element boundary value problems is verified through centrifuge tests on large-diameter monopiles. Furthermore, the model is adopted to analyze the dynamic response of monopile OWTs under seismic loading. The results indicate that, compared to cyclic shakedown, cyclic degradation leads to a progressive reduction in soil stiffness, which diminishes acceleration amplification, increases settlement accumulation, and results in higher residual excess pore pressure with greater fluctuation. Despite its advantages, this model requires a priori specification of the sign of the plastic modulus parameter cd to capture either cyclic degradation or shakedown behavior. Furthermore, under undrained conditions, the model leads pstabilization of the effective stress path, which subsequently results in underestimation of the excess pore pressure.

In order to investigate the frost-heaving characteristics of wintering foundation pits in the seasonal frozen ground area, an outdoor in-situ test of wintering foundation pits was carried out to study the changing rules of horizontal frost heave forces, vertical frost heave forces, vertical displacement, and horizontal displacement of the tops of the supporting piles under the effect of groundwater and natural winterization. Based on the monitoring condition data of the in-situ test and the data, a coupled numerical model integrating hydrothermal and mechanical interactions of the foundation pit, considering the groundwater level and phase change, was established and verified by numerical simulation. The research results show that in the silty clay-sandy soil strata with water replenishment conditions and the all-silty clay strata without water replenishment conditions, the horizontal frost heave force presents a distribution feature of being larger in the middle and smaller on both sides in the early stage of overwintering. With the extension of freezing time, the horizontal frost heave force distribution of silty clay-sand strata gradually changes from the initial form to the Z shape, while the all-silty clay strata maintain the original distribution characteristics unchanged. Meanwhile, the peak point of the horizontal frost heave force in the all-silty clay stratum will gradually shift downward during the overwintering process. This phenomenon corresponds to the stage when the horizontal displacement of the pile top enters a stable and fluctuating phase. Based on the monitoring conditions of the in-situ test, a numerical model of the hydro-thermo-mechanical coupling in the overwintering foundation pit was established, considering the effects of the groundwater level and ice-water phase change. The accuracy and reliability of the model were verified by comparison with the monitoring data of the in-situ test using FLAC3D finite element analysis software. The evolution of the horizontal frost heaving force of the overwintering foundation pit and the change rule of its distribution pattern under different groundwater level conditions are revealed. This research can provide a reference for the prevention of frost heave damage and safety design of foundation pit engineering in seasonal frozen soil areas.

This paper presents a rigorous, semi-analytical solution for the drained cylindrical cavity expansion in transversely isotropic sand. The constitutive model used for the sand is the SANISAND-F model, which is developed within the anisotropic critical state theory framework that can account for the essential fabric anisotropy of soils. By introducing an auxiliary variable, the governing equations of the cylindrical expansion problem are transformed into a system of ten first-order ordinary differential equations. Three of these correspond to the stress components, three are associated with the kinematic hardening tensor, three describe the fabric tensor, and the last one represents the specific volume. The solution is validated through comparison with finite element analysis, using Toyoura sand as the reference material. Parametric analyses and discussion on the impact of initial void ratio, initial mean stress level, at-rest earth pressure coefficient and initial fabric anisotropy intensity are presented. The results demonstrate that the fabric anisotropy of sand significantly influences the distribution of stress components and void ratio around the cavity. When fabric anisotropy is considered, the solution predicts lower values of radial, circumferential and vertical stresses near the cavity wall compared to those obtained without considering fabric anisotropy. The proposed solution is expected to enhance the accuracy of cavity expansion predictions in sand, which will have significant practical applications, including interpreting pressuremeter tests, predicting effects of driven pile installation, and improving the understanding of sand mechanics under complex loading scenarios.

Arsenic (As) contamination in soil presents significant challenges to plant growth and development, impacting agricultural productivity, food safety, ecosystem stability, and human health. This study investigates the effects of As toxicity on the medicinal plant Ocimum basilicum L. cultivar CIM-Saumya by assessing the impact of varying As concentrations (1, 5, 10, and 25 mg kg-1 of soil) on various physio-biochemical and microscopic parameters. Controlled experiments were conducted to assess the photosynthetic rate, gas exchange, and the activities of carbonic anhydrase (CA), Rubisco, and nitrate reductase (NR) enzymes. In addition, the concentrations of non-enzymatic antioxidants (proline, flavonoids, and phenolic compounds) and enzymatic antioxidants (superoxide dismutase (SOD), catalase (CAT), and peroxidase (POX) were analyzed. Alterations in glandular trichomes, essential oil (EO) content, and composition were also evaluated. Confocal laser scanning microscopy (CLSM) was utilized to examine root cell viability and detect reactive oxygen species (ROS). Our results revealed that As exposure significantly inhibited physio-biochemical activities in O. basilicum, with low As concentrations (1 mg kg-1) enhancing EO content by 18.75 %. However, higher As concentrations (25 mg kg-1) induced oxidative stress, evidenced by increased malondialdehyde (MDA), ROS accumulation, reduced trichome size and density, and smaller stomatal apertures. The highest As concentration resulted in a 53.12 % reduction in EO content. These findings demonstrate that O. basilicum exhibits differential responses to As stress, with low concentrations enhancing EO production, while high concentrations cause oxidative damage and reduced EO content, providing insights into the plant's adaptive strategies and potential alterations in its aroma and therapeutic properties under As stress.

Energy piles, which serve the dual functions of load-bearing and geothermal energy exchange, are often modeled with surrounding soil assumed to be either fully saturated or completely dry in existing design and computational methods. These simplifications neglect soil saturation variability, leading to reduced predictive accuracy of the thermomechanical response of energy piles. This study proposes a novel theoretical framework for predicting the thermo-hydro-mechanical (THM) behavior of energy piles in partially saturated soils. The framework incorporates the effects of temperature and hydraulic conditions on the mechanical properties of partially saturated soils and pile-soil interface. A modified cyclic generalized nonlinear softening model and a cyclic hyperbolic model were developed to describe the interface shear stress-displacement relationship at the pile shaft and base, respectively. Governing equations for the load-settlement behavior of energy piles in partially saturated soils were derived using the load transfer method (LTM) and solved numerically using the matrix displacement method. The proposed approach was validated against experimental data from both field and centrifuge tests, demonstrating strong predictive performance. Specifically, the average relative error (ARE) was less than 15% for saturated soils and below 23% for unsaturated soils when evaporation effects were considered. Finally, parametric analyses were conducted to assess the effects of flow rate, groundwater table position, and softening parameters on the THM behavior of energy piles. This framework can offer a valuable tool for predicting THM behavior of energy piles in partially saturated soils, supporting their broader application as a sustainable foundation solution in geotechnical engineering.

The thermo-mechanical (TM) behaviour of the energy pile (EP) group becomes more complicated in the presence of seepage, and the mechanism by which seepage impacts the EP group remains unclear.In the current work, a 2 x 2 scale model test bench of EP group was set up to investigate the TM behaviour of EP group with seepage. The test results indicate that the heat exchange performance of EP group with seepage can be significantly enhanced, but also leads to obvious differences in the temperature distribution of pile and surrounding soil along the seepage direction, and thus causes evident differences in the mechanical properties between the front pile and the back pile in pile group. Compared with the parallel connection form, the thermal performance of EP group with the series connection form is slightly attenuated. However, the mechanical properties of various piles in the EP group differ significantly. Under the action of seepage, the mechanical balance properties of various piles in the forward series form are optimal, followed by the parallel form, and the reverse series form is the least optimal. A 3-D CFD model was established to further obtain the influence of seepage and arrangement forms on EP group. The findings indicate that seepage can not only mitigate thermal interference between distinct piles but also expedite the process of heat transfer from pile-soil to reach a state of stability. Concurrently, the thermal migration effect induced by seepage will be superimposed along the seepage direction, resulting in the elevation of thermal interference of each pile along the seepage direction, and the superposition of thermal migration effect increases with the time. Under the same seepage condition, the cross arrangement can enhance the thermal performance of EP group, optimize the temperature distribution of pile and soil, and thus the imbalance of mechanical properties among pile groups can be reduced. In addition, the concepts of thermal interference coefficient and heat exchange rate per unit soil volume are introduced to facilitate a more precise evaluation of the thermal interference degree of each pile in the pile group and the heat exchange performance under different pile arrangement forms.The standard deviation and mean value in the statistical method are used to evaluate the equilibrium of mechanical properties of pile group, which is more intuitive to compare the differences in mechanical properties of pile groups under different working conditions.

Maximizing agricultural tractor energy efficiency is crucial for sustainable farming. Tractors are one of the most popular machines in use in agriculture, and much of their use is dedicated to drawbar operations. Under these conditions, only up to 70 % of engine power is transferred to the soil, and this may even drop to 50 % on soils with poor mechanical properties. Recently, tyres which meet very high flexion standards have hit the market and to date, no study has performed a thorough full-vehicle traction analysis of vehicles equipped with such standards. This paper investigated the influence of tyres on vehicle performance and efficiency. Moreover, a cost analysis of the new tyre technology was carried out to assess the duration of use necessary for farmers to recoup the financial investment this new tyre technology requires. The analysis comprised steady-state drawbar tests on two soil types using a tractor rated at 230 kW and equipped with wheel force transducers. Key performance indicators were calculated from the collected data. Results showed superior traction on softer soil, where the mean vehicle traction ratio was 6.4 % higher than on firmer soil, highlighting tyre set performance differences. However, traction efficiency was 17.5 % greater on firmer soil. Very high flexion tyres resulted in improved indicators in both soils and despite the greater cost of tyres using the new standard, farmers may obtain economic benefits even within a year if such tyres are mostly used in field operations and on soft soils.

Friction characteristics are critical mechanical properties of clay, playing a pivotal role in the structural stability of cohesive soils. In this study, molecular dynamics simulations were employed to investigate the shear behavior of undrained montmorillonite (MMT) nanopores with varying surface charges and interlayer cations (Na+, K+, Ca2+), subjected to different normal loads and sliding velocities. Consistent with previous findings, our results confirm that shear stress increases with normal load. However, the normal load-shear stress curves reveal two distinct linear regions, indicating segmented friction behavior. Remarkably, the friction coefficient declines sharply beyond a critical pressure point, ranging from 5 to 7.5 GPa, while cohesion follows an inverse trend. The elevated friction coefficient at lower pressures is attributed to the enhanced formation of hydrogen bonds and concomitant changes in density distribution. Furthermore, shear strength was observed to increase with sliding velocities, normal loads, and surface charges, with Na-MMT exhibiting superior shear strength compared to KMMT and Ca-MMT. Interestingly, the friction coefficient shows a slight decrease with increasing surface charge, while ion type exerts a minimal effect. In contrast, cohesion is predominantly influenced by surface charge and remains largely unaffected by ion type, except under extreme pressures and velocities.

The stress state and density of soil have been considered as the key factors to determine the liquefaction resistance. However, the results of seismic liquefaction case histories, laboratory tests and centrifuge model tests show that the fabric characteristics also influence liquefaction resistance, even more significantly than the contributions of stress state and density. In this study, anisotropic specimens with different consolidation histories were prepared using the 3D Discrete Element Method (DEM) to investigate the influence of fabric characteristics on the mechanical behavior of granular materials and the underlying mechanisms. The simulations revealed that under monotonic shear conditions, horizontally anisotropic specimens exhibited strain hardening and dilatancy characteristics, as well as higher peak strength. Under cyclic shear condition, the normalized liquefaction resistance of the specimens showed a strong linear relationship with the degree of anisotropy, independent of confining pressures and density. Microscopic results indicate that the fabric arrangement aligned with the loading direction leads to the evolution of the mechanical coordination number and average contact force in a manner favorable to resisting loads, which is the underlying mechanism influencing macroscopic mechanical properties. Additionally, the evolution patterns of contact normal magnitude and angle in anisotropic granular materials under cyclic loading conditions were also analyzed. The results of this study provided a new perspective on the macroscopic mechanical properties and the evolution of the microstructure of granular soils under anisotropic conditions.

High-strength mortar (HSM) gradually has wide applications due to its exceptional strength, micro-expansion properties, and excellent fluidity. Behavior deterioration of structures in saline soil areas is primarily attributed to freeze-thaw cycles and sulfate attack. In this study, the coupling effect of freeze-thaw cycles and sulfate attack on the appearance, mass loss, and relative dynamic elastic modulus of HSM was investigated during erosion. Then, compressive experiments were conducted to assess the mechanical properties of HSM subjected to both freeze-thaw cycles and sulfate attack. The influences of coupling freeze-thaw cycles and sulfate attack on the compressive properties of HSM were quantified through regression analysis of experimental results. Empirical models for compressive stress-strain curves and damage constitutive behavior of HSM were developed, taking the coupled adverse effect into account. The results indicate that the coupled effect of freeze-thaw cycles and sulfate attack causes performance deterioration of HSM. The empirical models reproduce the compressive behaviors of HSM subjected to freeze-thaw cycles and sulfate attack.