The salt concentration of the pore solution can alter the micro-pore and particle structure of soil, thereby affecting its engineering properties. To investigate the compression characteristics of marine soil under different salt concentrations, one-dimensional compression and SEM scanning tests were conducted on marine reconstituted clay from the Yellow Sea with varying NaCl concentrations (0-5%). The effects of NaCl concentration on the compression characteristics and microstructure of marine sedimentary clay were analyzed. The results indicate that: (1) Compressibility increases up to a NaCl concentration of 2.5%, after which it declines. At 2.5% NaCl threshold concentration, the coefficient of compression, compressibility index, and consolidation coefficient reach their peak values, and the response becomes more pronounced with increasing compression pressure. During the secondary compression stage, as pore water is expelled, the impact of NaCl concentration on compressibility diminishes, while the rebound characteristics remain unaffected by NaCl concentration; (2) SEM analysis reveals that at a NaCl threshold concentration of 2.5%, the pore fractal dimension, particle fractal dimension, pore anisotropy, and particle anisotropy reach their maximum values, with the most complex shape and pores and particles aligning in the same direction. When the concentration is less than 2.5%, the soil exhibits narrow pores and rounded particles upon compression. When the concentration exceeds 2.5%, the microstructure changes in the opposite direction, confirming the particle rearrangement mechanism driven by surface contact under moderate salinity. At the threshold concentration of 2.5%, a balance between electrostatic forces and attractive forces enables stable surface-to-surface contacts, maximizing compressibility. The findings of this study provide valuable references for the foundation design of marine geotechnical engineering in specific sea areas, thereby enhancing the safety and reliability of related projects.

The objective of the current study is to explore the effect of biostimulation treatment methods on the mechanical properties and microstructure characteristics of biocemented soil. Biostimulated microbially induced carbonate precipitation (MICP) is an eco-friendly and economical soil reinforcement measure. It relies on the stimulation of the urease-producing bacteria (UPB) in situ for the MICP process. Different biostimulation treatment methods involve different oxygen availability, stimulation solution content and distribution, and number of biostimulation treatments. There may be differences in the effect of UPB stimulation and biocementation when different biostimulation treatment methods are used. In this study, four biostimulation treatment methods, i.e., unsaturated single biostimulation treatment (USBT), unsaturated multiple biostimulation treatments (UMBT), saturated single biostimulation treatment (SSBT) and saturated-unsaturated-combined single biostimulation treatment (CSBT), were used to stimulate native UPB in soil columns, and then, the same cementation treatment was applied to the soil columns. Subsequently, the mechanical behavior and microstructural properties of the biocemented soil were investigated. The results indicated that the saturated single biostimulation treatment was more conducive to stimulating native UPB to induce CaCO3 precipitation. Samples subjected to the saturated single biostimulation treatment exhibited higher CaCO3 precipitation content (CCP), dry density, unconfined compressive strength (UCS) and lower permeability within the same cementation treatment cycle (NC). However, UCS was not only determined by CCP, but was also regulated by CaCO3 spatial distribution and precipitation pattern. This study could help guide the selection of biostimulation treatment methods.

For the soft-plastic loess tunnel engineering, collapse and damage of the surrounding rock during excavation are often driven by the combined action of the seepage water and the unloading effect. Under water pressure and unloading, the soil suffers complex stress-seepage coupling action causing the inevitable change of permeability and mechanical properties. In this paper, seepage control devices were added to the GDS test device, and a new triaxial permeability measurement system was developed. Triaxial unloading-seepage tests were conducted on soft-plastic loess under the effect of hydraulic coupling. The variation of permeability characteristics of Q(2) type soft-plastic loess under lateral unloading and the soil mechanical characteristics under different seepage pressure were analyzed. Meanwhile, microstructure characteristics of soft-plastic loess during the triaxial test were obtained by scanning electron microscope to clarify the deformation and seepage mechanism. The results show that the strength of soft-plastic loess decreases significantly with the increase of osmotic pressure. Under the condition of 50 and 100 kPa osmotic pressure, the cohesive force of soft-plastic loess decreases by 15.5% and 39.0% and the friction angle decreases by 9.4% and 22.6%, respectively. The permeability coefficient of loess increases slowly at first and then increases rapidly during the unloading process. The main reason for the significant increase of permeability coefficient is the penetration of soil fissures and the formation of shear bands after entering the plastic deformation stage.