Colluvial landslides develop in loose Quaternary deposits, with deformation generally being progressive and crack development dominant in the sliding mass surface layer. With the Tanjiawan landslide in the Three Gorges Reservoir (China) as a case study, field investigations, deformation monitoring, and groundwater level monitoring data were integrated to analyze the landslide deformation characteristics and elucidate the influence of cracks on its deformation. We used numerical simulations, including the finite element and discrete element methods, for investigating the progressive deformation mechanism of rainfall-triggered landslides in the accumulation layer and predicting the failure process. The results indicated that crack formation instigated a preferential seepage channel in the shallow layer of the sliding mass, rainfall infiltration along cracks generated water pressure, and the landslide gradually morphed from a stable into a step-like progressive deformation state. Preferential flow inside the cracks effectively elevated the groundwater level within the landslide, and either the number or depth of cracks significantly affected the groundwater seepage field, thereby influencing slide stability. Geological conditions controlled the deformation and failure processes of each landslide section. The uplifted bedrock on the right side blocked the sliding process of the rear sliding mass, and the middle and front sliding masses moved faster but the sliding distance was shorter. The deformation trend is deformation, crack formation, preferential flow occurrence, crack extension, and deformation. The ultimate cause of failure was a steep rise in groundwater level following short duration heavy rainfall or long duration light rainfall.
The process of permeation damage of the filling medium in the fracture is critical to the stability of the fractured rock mass. This study focused on the seepage failure process of filling materials in fractures and faults. To investigate the effects of axial stress and clay content, a series of experimental tests were conducted on internally unstable granular soil specimens with different clay contents under different axial stresses. The variations of flow rate and hydraulic conductivity were recorded and analyzed during the tests, and the typical process of seepage failure was summarized. The flow rate, hydraulic conductivity, and their growth rates were found to be smaller under high axial stress compared to low axial stress, and the flow rate of samples with higher clay content was smaller than those with lower clay content. Initially, the hydraulic conductivity decreased slightly due to clay and fine particle rearrangement, and remained nearly constant when the hydraulic gradient was small. However, as the hydraulic gradient increased, the hydraulic conductivity began to increase in response to the loss of clay and fine particles.
Loess area is the region that geohazards happened most frequently, accounting for 1/3 of the geohazards in China. Cutting slope has become the most prominent products in human engineering activities and slope failure induced by rainfall has become the main form in recent years. Well-instrumented centrifuge model tests have been introduced to investigate the failure process and failure pattern, including pore water pressure, progressive deformation-failure process and characteristic of the high cutting slope by rainfall. The results show that rainfall induced loess slope failure is characterized by shallow slide to flow and two deeper creepage sliding-tension surfaces. All the sliding faces are characterized by planar surfaces parallel to slope surface. The planar sliding surface differs a lot to the circular sliding surface in the gravitational soil landslide. The accumulative deformation especially the abrupt displacement before failure induced the excess pore water pressure, after which flow failure with high-speed happened. The pore-water transducers on both sides of the shallow sliding surface have distinct response to slope deformation. The quantitative monitoring data indicates that the liquefaction is not the reason but the result of the deformation accumulation and big transient deformation.
The problems of gully and soil erosion caused by large-scale urban construction and agricultural development in China have become more and more serious in recent years. In an effort to solve this problem, a series of gully stabilization and highland protection projects have been carried out on the Loess Plateau, and this has resulted in a large number of high-loess-filled-slopes (HLFSs). Although these filled slopes uses several different mitigation measures, the HLFSs have been eroded and destroyed under the action of water. In order to study the influence of different mitigation measures on the stability of HLFSs and their failure process, this paper uses a flume test of the effects of various mitigation measures on this failure process. The results show that: (1) the failure processes of slopes with different mitigation measures are obviously different. Slope deformation u with a declining gradient mitigation mainly occurs on the surface of the slope body, and although slope erosion is quite serious, the slope does not fail as a whole. Slopes with a stepwise drainage channel mitigation show little erosion, but material can easily slide along the horizontal drainage channels. (2) The slope deformation process is correlated with changes in pore-water pressure. When local instability occurs, there is always a pre-process of continuously rising pore-water pressure. When a failure occurs, the pore-water pressure of the soil at each position of the slope body suddenly fluctuates under instantaneous excitation. (3) The response of soil pore pressure and the development characteristics of tension cracks affect the deformation of the slopes, which is also the cause of the differences slope instability caused by different mitigation measures. These research results provide reference for the protection of HLFS engineering projects from heavy rains.