There has been a growing interest in controlled low strength material CLSM due to its engineering features, such as self-leveling and early strength development, as well as it potential for utilizing industrial waste. Still, the dynamic properties on CLSM are rarely studied. This study evaluates the feasibility of red mud as a partial aggregate replacement in foamed-lightweight CLSM, incorporating high-carbon fly ash and preformed foam. We varied both the red mud contents RMc and foam volume ratio FVR within the mixtures and examined their impact on unconfined compressive strength and dynamic properties including shear modulus G and damping ratio D. The results reveal that the red mud enhances foam stability, leading to more uniform pore structures and increased porosity, which reduces bulk densities. Despite higher porosity, red mud serves as a strong alkaline activator, enhancing geopolymer reactions of high-carbon fly ash and thereby increasing both compressive strength and initial shear modulus G0. Interestingly, increasing FVR had minimal impact on the D, while higher RMcnotably increased D, highlighting its distinct role in energy dissipation. The red mud-incorporated foamed CLSM exhibits strain-dependent normalized shear modulus G/G0 comparable to that of gravel, while its D is 40-100 % higher than gravel or gravelly soil at shear strain of 1.10-5, which corresponds to typical traffic-induced vibration levels. Moreover, theoretical volumetric-gravimetric relationships are introduced to account for the combined effects of FVR and RMcon CLSM behavior. These findings demonstrate that the red mud included foamed CLSM can be utilized as advanced structural backfill material capable of effectively mitigating the vibrations induced by traffic, low-amplitude seismic events, and mechanical sources.

This study investigates the utilization of titanium gypsum (TG) and construction waste soil (CWS) for the development of sustainable, cement-free Controlled Low Strength Material (CLSM). TG, combined with ground granulated blast furnace slag, fly ash, and quicklime, serves as the binder, while CWS replaces natural sand. Testing thirteen mixtures revealed that a CWS replacement rate of over 40% controls bleeding below 5%, with a water-to-solid ratio between 0.40 and 0.46, ensuring flowability. Higher TG content reduces flowability but is crucial for strength due to its role in forming a crystalline network. Compressive strength decreases with higher TG and water-to-solid ratio, while 3-5% quicklime provides a 56 day strength below 2.1 MPa. Higher CWS reduces expansion, and TG content between 60% and 70% minimizes volume changes. XRD and SEM analyses underscore the importance of controlling TG and quicklime content to optimize CLSM's mechanical properties, highlighting the potential of TG and CWS in creating low carbon CLSM.

Civil excavation projects frequently yield substantial excess spoil, posing challenges to sustainable construction. This study explores repurposing such spoil for creating controlled low strength material (CLSM), emphasizing the novel use of polycarboxylate superplasticizer (PCE) to reduce the water requirement. The work also distinctively utilizes water film thickness (WFT) theory to elucidate the effects of PCE dosage and WFT on material properties, thereby advancing CLSM mix design. First, using an experimental approach, a series of fresh CLSM samples are prepared, with varying the water-to-solid ratio (W/S) and PCE dosage, to evaluate their packing density, WFT, flowability, and bleeding rate. It is demonstrated that both packing density and WFT experienced a non-linear increase with rising PCE dosage. Regression analysis of the experimental data reveals that the flowability and bleeding rate linearly increase with the rising WFT, and the enhancements are more pronounced at higher PCE dosage. Notably, at a given WFT, the impact of PCE dosage on flowability and bleeding rate reduce as WFT decreases. Additionally, the research identifies specific WFT thresholds correlating with maximum flowability and a 5% bleeding rate. These thresholds mark the critical point at which WFT ceases to influence flowability and delineate the maximum WFT that satisfies the bleeding rate requirements, respectively. These insights are important for optimizing the design of CLSM with PCE in terms of flowability and bleeding rate.

The volume of shield tunnel spoil (STS) is very large, its effective management is difficult, and it even causes environmental pollution. In this study, to achieve its recycling, a novel controlled low strength material (CLSM) was prepared by utilizing high fine-grained STS as partial aggregates instead of sand, and its engineering performance was thoroughly evaluated. In the process of mix proportion design, key parameters such as the STS-tototal aggregate ratio (TS/TA), foam agent content (F), water-to-binder ratio (W/B), binder-to-total aggregate ratio (B/TA), and fly ash-to-cement ratio (FA/C) were employed. Workability aspects (i.e., flowability, bleeding rate, and setting time) and physical and mechanical properties (i.e., unconfined compressive strength and density) were evaluated. Additionally, the pH of bleeding and leachate, as well as the impact of foam agent content on CLSM properties, were examined. The findings revealed that an increase in the TS/TA ratio was associated with a decrease in flowability, density, and compressive strength, as well as an extension in setting time. The CLSM, with a flowability range of 150-300 mm, exhibited a bleeding rate below 2%, setting times between 3.6 and 6.1 hours, 28-day strength ranging from 1.06 to 3.24 MPa, and fresh density ranging from 1810 to 2060 kg/m3. Generally, these results met the required specifications, although the fresh density was slightly lower. The pH results indicated that the CLSM is non-corrosive. Furthermore, our investigation highlighted the substantial influence of foam agent content on flowability and setting time. An increase of 0.1 parts per thousand in the proportion of foam agent within the total aggregates resulted in a flowability increase of 2.1-2.6 mm and a setting time increase of 4.25-4.99 minutes. Therefore, it is feasible to utilize high fine-grained STS in the production of CLSM.