This research evaluated the effects of various percentages of crumb rubber, tire scrap fibers, palm fibers, polymer bags fibers, palm ash, and polypropylene fibers on the compaction and compression behavior of clayey sand stabilized with cement. The results of compaction tests showed the maximum dry density decreased as the proportions of these waste materials and cement increased. The most suitable moisture content of soil decreased by increasing the percentages of crumb rubber, tire scrap fibers, and polymer bag fibers, but increased by increasing the percentages of palm fibers, palm ash, polypropylene fibers, and cement. Compared to other wastes, palm fibers had a more substantial effect on the compaction and strength properties of the stabilized soil due to its uniform distribution in the soil and stronger bonding between the soil particles. Moreover, the specimens stabilized with 1% polypropylene fibers and 6% cement showed the best ductility behavior.

This study examines the use of low-value rice husk ash as a stabilizer to optimize the mechanical performance and strength of compressed earth blocks made with local soil from the Cauquenes Province, Chile. The use of locally sourced earth construction materials in Chile is limited by their lower compressive strength compared to conventional fired bricks, along with the demanding seismic conditions of the region. To address these limitations, this study details the methodology for collecting, preparing, and mixing raw materials to manufacture compressed earth blocks, compacted under 10 MPa using a novel cylindrical polylactic acid mold designed for miniaturized samples. Fourteen different samples representing nine mixtures of rice husk ash and soil were evaluated using an optimized experimental design. The resulting mechanical properties, including fracture analysis correlated with performance, were assessed through statistical analysis to determine the significance of the optimum mix and the observed trends in strength, modulus of elasticity, yield strength, and associated plastic work. The maximum compressive strength achieved was 3.3 MPa. Notably, the optimum mix of rice husk ash-stabilized compressed earth blocks exhibited a 60% increase in strength compared to pure soil compressed earth blocks, demonstrating the potential of rice husk ash as a cement substitute.

In recent decades, heavy industrial discharges have caused severe soil and groundwater pollution. Many areas previously occupied by industries are now represented by lands contaminated by the accumulation of toxic metals, which pose serious risks to human health, plants, animals, and surrounding ecosystems. Among the various potential solutions, the solidification and stabilization (S/S) technique represents one of the most effective technologies for treating and disposing of a wide range of contaminated wastes. This study focuses on the theoretical definition of a green material mix, which will subsequently be used in the solidification process of contaminated industrial soils, optimizing the mix to ensure treatment effectiveness. The mix design was developed through a literature analysis, representing a preliminary theoretical study. This paper explores the application of the S/S process using various additives, including Portland cement, fly ash (FA), ground granulated blast furnace slag (GGBFS), and other industrial waste materials, to create an innovative mix design for the treatment of contaminated soils. The main objective is to reduce the permeability and solubility of contaminants while simultaneously improving the mechanical properties of the treated materials. The properties of the studied soils are described along with those of the green materials used, providing a comprehensive overview of the optimization of the resulting mixtures.

In the present research the durability and geotechnical properties of an expensive clayey soil stabilized by two different compositions of additives were investigated and compared. The first composition consisted of environmentally and ecofriendly materials: BOF steel slag ranging from 0-20% as well as rice husk ash (RHA) ranged 0-16%wt of dry soil. The other composition consisted of relatively new generation of materials including nanomaterials: nano-CaCO3 as well as nano-SiO2. Atterberg limits test, free swell percent test, swelling pressure test and unconfined compressive test were used to assess the stabilizers influences upon expansive soil geotechnical characteristics. Also, the recurrent wet-dry cycles test was exerted on experimental and non-experimental samples for estimating stabilizers effects on durability. According to the results, each of the BOF slag and RHA enhances the expansive soil properties individually, while combination of slag-RHA led to better improvement of the soil properties. Also, the composition of nano-CaCO3 and SiO2 dramatically improved the clay soil operation. The optimum values of slag+RHA were suggested as 20% slag+12% RHA to enhance percent of swelling, pressure of swelling in addition to UCS as much as 95%, 96%, and 370%, respectively. The optimum value for the second stabilizer in this study was found to be 2%nano-SiO2+2% nano-CaCO3 which led to 318% increase in UCS and 86% decrease in swelling pressure.

This paper presents an extensive comparative analysis of the experimental results of chemical stabilisation of clayey soil in laboratory conditions by comparing the effects of adding conventional stabilisers (lime, cement binder), stabilisers that can be considered as waste material (fly ash, rock flour), as well as alternative chloride-based materials (ferric chloride, calcium chloride, potassium chloride) on the geomechanical properties of the soil. With the aim of determining the stabiliser optimal content in the mixture with the soil, in the first part of the research, the effects of stabilisation of clayey soil of medium plasticity using the considered stabilisers with different percentage share on the change in uniaxial compressive strength (UCS) and pH value of the soil at different time intervals after the treatment were analysed. In the second part of the research, additional tests were conducted on soil samples with optimal content for each of the considered stabilisers by monitoring changes in the physical and mechanical properties of the soil. These include Atterberg's limits (liquid limit and plasticity limit), modulus of compressibility in the oedometer, California bearing ratio (CBR), and swelling potential at different time intervals after the chemical treatment to determine the durability of stabilisation effects. The results of the conducted research reveal that each of the conventional, waste, and alternative materials considered as chemical stabilisers contributes to the improvement of the geomechanical properties of the clayey soil, primarily in terms of increasing the bearing capacity and reducing the swelling of the treated soil.

Dispersivity has long been a major concern in civil and geo-environmental engineering, as well as in agricultural engineering and soil sciences. Dispersive clay soils are common, but their prevalence and characteristics vary greatly across different regions of the world, especially in arid and semi-arid areas. These soils are highly unstable and prone to erosion when exposed to water, due to their high concentration of exchangeable sodium ions and large specific surfaces. This can cause serious damage to hydraulic infrastructure. However, identifying and stabilizing dispersive clay soils is crucial for infrastructure projects, as the use of untreated soils can result in irreversible and catastrophic failures due to internal erosion and piping. The systematic management of dispersive clays is crucial to prevent the wastage of fertile agricultural land and land designated for engineering construction. Although industrialization has numerous benefits, it often results in large quantities of waste byproducts that must be managed appropriately to reduce their environmental impact. The reuse of these wastes in soil improvement has become an increasingly popular approach to address both environmental pollution and cost-effectiveness concerns. Despite the growing interest in using waste by-products for soil stabilization, there is a lack of a systematic and comprehensive review of the management, mechanisms, identification systems, and improvement strategies for both traditional and non-traditional stabilizers. Therefore, there is an urgent need to review the available literature to provide a comprehensive understanding of the use of waste by-products for soil stabilization. Such a review could aid in the creation of soil stabilization methods that are both efficient and enduring while minimizing the environmental impact of waste by-products.

Various problems are often encountered during the backfilling process of deep foundation pits. The development of low-cost and efficient solidified materials for the preparation of fluidized solidified soil is currently an ideal solution. This article used industrial solid waste (granulated blast furnace slag, fly ash, carbide slag, etc.) as the main raw material to study the hydration hardening properties of solidified materials and the construction feasibility of fluidized solidified soil prepared from solid waste materials. The results are as follows: Compared with cement-based materials, solid waste-based solidified materials had lower early activity. The cumulative heat release within 72 h was less than 200 J/g. Different solid wastes, such as fly ash and carbide slag, had different effects on the properties of solidified materials. Overall, they had the potential to prepare fluidized solidified soil. The prepared fluidized solidified soil had a fluidity greater than 350 mm, a 28d compressive strength greater than 3 MPa, and exhibited good workability and excellent mechanical properties. Hydration products such as CS -H and AFt were filled in the soil structure. The 28d compressive strength well above the design requirements of general engineering projects. Meanwhile, the prepared fluidized solidified soil had good adaptability to conventional water reducers (fluidity could be increased by more than 40%) and early strength agents (1d compressive strength could be increased by more than 60%).

Searching for alternative material options to reduce the extraction of natural resources is essential for promoting a more sustainable world. This is especially relevant in construction and infrastructure projects, where significant volumes of materials are used. This paper aims to introduce three alternative materials, crushed ground glass (GG), recycled gypsum (GY) and crushed lime waste (CLW), byproducts of construction industry geomaterials, to enhance the mechanical properties of clay soil in Cartagena de Indias, Colombia. These materials show promise as cementitious and frictional agents, combined with soil and cement. Rigorous testing, including tests on unconfined compressive strength (qu) and initial stiffness (Go) and with a scanning electron microscope (SEM), reveals a correlation between strength, stiffness and the novel porosity/binder index (eta/Civ) and provides mixed design equations for the novel geomaterials. Micro-level analyses show the formation of hydrated calcium silicates and complex interactions among the waste materials, cement and clay. These new geomaterials offer an eco-friendly alternative to traditional cementation, contributing to geotechnical solutions in vulnerable tropical regions.

The use of appropriate waste materials to stabilize problematic soils, such as expansive soils that are responsible for geotechnical damage, is a common practice in geotechnical engineering. This study presents the use of pulverized ash from the combustion of pine cone (PC) waste as a stabilizing agent to improve the engineering properties of expansive soils. A series of laboratory tests were carried out to examine the effect of different percentages of pine cone ash (PCA) content (3%, 5%, 7%, and 10%) on the Atterberg limits, swelling potential (Sp), linear shrinkage, compressibility, and unconfined compressive strength (q u ) of naturally occurring swelling soils and the PC ash -treated soils. The results showed that PC ash contents of 5% and 7% contributed to a significant reduction in the swelling and shrinkage potential and an improvement in the coarsest texture, brittleness behavior, compaction properties, and compressive strength of the treated soils. Conversely, PC ash contents below 3% and above 7% showed minimal changes in the index and engineering properties of the PC ash -treated soils. In particular, the PC ash content of 5% resulted in optimal mitigation of the poor properties of the treated soils. The use of pine cone ash as a stabilizing agent represents a suitable and complementary subgrade soil material for expansive soils on which lightweight structures are built.