Microbially induced calcium carbonate precipitation (MICP) technology is an emerging and environmentally sustainable method for improving the strength and stiffness of soil. Specifically, this innovative approach has gained favor in marine engineering due to the advantaged compatibility between precipitated calcium carbonate induced by MICP and coral sand. Sand containing fines is susceptible to liquefy. Whereas, the impact of fines contents on cyclic behavior of MICP-treated calcareous sand remains uncertain. Consequently, this technical note aims to investigate the liquefaction behavior of biocemented calcareous silty sand by conducting undrained cyclic triaxial shear tests and microscopic analysis. The results revealed the patterns of the excess pore water pressure curves and cyclic deformation characteristics as the fines contents increased. The liquefaction resistance of biocemented sand initially decreases with the addition of fines but subsequently exhibits an increasing trend. Microscopic analysis showed that at the cementation level with the cementation solution concentration of 1 mol/L, the calcium carbonate crystals are mainly attached to the surface of sand grains and this pattern does not directly affect the force chain.

Understanding accurately the influence of non-plastic fines on stress-dilatancy of coral sand mixture-packing is crucial for marine engineering in various geotechnical applications. This work experimentally examined the effects of non-plastic fines and initial test conditions on stress-dilatancy behavior of mixture. Based on test results, equivalent void ratio (e*\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${e}{*}$$\end{document}) was determined to quantify the global effect of fines on shear behavior across different shear stages. Test results show that e*\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${e}{*}$$\end{document} exhibits a reduction as the mean effective stress (p '\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${p}{\prime}$$\end{document}) increases, following a power function relationship. Besides, e*\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${e}{*}$$\end{document} variation under phase transformation, peak state, and critical state can be described by a normalized curve. Reduced fines content and increased relative density can contribute to the enhancement of both peak strength and internal friction angle within the mixture. However, the smooth shape and lubrication function facilitated by fines actively contribute to initiation of shear contraction. Furthermore, the stress paths observed in the CD shear tests manifest as a sequence of parallel straight lines within the q\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$q$$\end{document}-p '\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${p}{\prime}$$\end{document} plane. The length of these lines progressively extends as the stress level escalates. Moreover, deviator stress in q\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$q$$\end{document}-p '\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${p}{\prime}$$\end{document} curves under character state presents lower and upper limits which are 0.334 and 0.639 corresponding to tested samples determined by fines content and relative density. Elevated fines content combined with reduced relative density can lead to a reduction in both peak-state friction angle and maximum angle of dilation.

The naturally deposited soil usually does not consist of pure coarse or fine-grained soil but of a mixture of both. The mechanical behaviour of a saturated fine sand mixed with varying amounts of low-plastic fines was evaluated by monotonic as well as high-cyclic triaxial tests. The test results were used to conclude on the effect of fines content on the critical state, phase transformation line, secant Young's modulus, the residual strain accumulation as well as strain amplitude during drained cycles of the mixtures in relation to the global void ratio as well as to the equivalent void ratio. It was found that while the choice of void ratio definition is important for the uniqueness of the critical void ratio, both approaches can be used as state variables for the phase transformation line. However, some seemingly contradictive results are found from the drained high-cyclic tests. Eventhough, an increase of the residual strain accumulation with decreasing fines content compared at the same initial equivalent void ratio is rendered by the laboratory data, a unique and on fines content independent relationship between eacc could be established only with respect to the initial global void ratio.