As a newly emerged solution for supporting the new generation of offshore wind turbines (OWTs), the pile-bucket foundation has received wide attention. However, little attention has been paid to the grouted connection that connects the monopile and bucket foundation. As the loadtransferring, yet vulnerable component, the fatigue mechanism of the grouted connection and its influence on the cyclic laterally-loaded response of OWT foundation are still not clear. In this study, a sophisticated three-dimensional (3D) finite element (FE) model of the pile-bucket foundation with grouted connection is constructed, which incorporates a hypoplastic clay model and the concrete damage plasticity (CDP) to consider the cyclic load effect on both soil and grout material. A modal analysis is first performed to verify the rationality of the proposed model. Then the influence of cyclic load frequency, load amplitude and stiffener arrangement on the accumulation of pile head displacement, stress distribution and crack development of the grouted connection is systematically analyzed. Results indicate that as load frequency approaches the eigen-frequency, the OWT structure tends to vibrate more intensively, leading to stress concentration and fatigue damage of the grouted material and rapid accumulation of the pile-head displacement. The influence of load amplitude on grout damage seems to be limited in the contact area in the simulated cases. Meanwhile, the installation of stiffeners slightly mitigates the pile head displacement accumulation, but also raises the risk of stress concentration and fatigue damage of the grouted connection. The numerical results reveal the load-transferring function and fatigue damage of the grouted connection, which could provide some reference for an optimized structure and dynamic design for the pile-bucket foundation under cyclic load.

Piled raft foundations are increasingly used in construction due to their cost efficiency, requiring fewer piles than traditional pile foundations. Their ability to withstand cyclic lateral loads, such as those from earthquakes and wind forces, is crucial for structural stability. Understanding their response under cyclic loading conditions is essential, and finite element modeling (FEM) is a valuable tool for analyzing these behaviors. A recent 3D FEM study examined the performance of piled raft foundations in clay soils, focusing on loading pattern, frequency, and number of cycles. Results showed that lateral load capacity decreased as cycle count and frequency increased, with full cyclic loading (FCL) having a more pronounced effect than half cyclic loading (HCL). The raft shared 20.57-39.07 % (HCL) and 27.68-55.13 % (FCL) of lateral loads at frequencies of 0.1-10 Hz over 20 cycles. Additionally, locked-in moments increased by 21 %, and the degradation factor ranged from 65 to 80 % for HCL and 70-90 % for FCL. These findings provide valuable insights into pile-soil interaction and foundation stability under cyclic lateral loading, ensuring more effective design strategies for structures exposed to dynamic forces. Future research should explore long-term cyclic effects to further optimize foundation performance.

It is well known that piles embedded in sand accumulate lateral deformation (displacement and rotation) when subjected to horizontal cyclic loading. The rate of accumulation depends on various parameters, such as loading conditions and properties of the pile-soil system. For nearly rigid piles, such as monopile foundations for offshore wind turbines, an essential aspect is the type of loading, which is determined by the ratio of the cyclic minimum load to cyclic maximum load. Several studies have shown that asymmetric two-way loading generally results in larger accumulated pile deformation compared with other types of loading, especially oneway loading with complete unloading in each cycle. This article presents the planning, execution, and evaluation of physical 1g small-scale model tests on the deformation accumulation of laterally loaded rigid piles due to cyclic loading focusing on soil deformations resulting from various cyclic load ratios. To visualize soil deformation fields and rearrangement processes within the soil profiles, particle image velocimetry (PIV) was applied in the tests. The evaluation of the model test results provides insights into varying accumulation rates and highlights the capabilities as well as limitations of PIV. The observations are summarized under the of findings, which may assist in planning future PIV experiments.

Concrete-filled FRP (Fiber Reinforced Polymer) tube composite piles offer superior corrosion resistance, making them a promising alternative to traditional piles in marine environments. However, their performance under cyclic lateral loads, such as those induced by waves and currents, requires further investigation. This study conducted model tests on 11 FRP composite piles embedded in sand to evaluate their behavior under cyclic lateral loading. Key parameters, including loading frequency, cycle count, loading mode, and embedment depth, were systematically analyzed. The results revealed that cyclic loading induces cumulative plastic deformation in the surrounding soil, leading to a progressive reduction in the lateral stiffness of the pile-soil system and redistribution of lateral loads among piles. Higher loading frequencies enhanced soil densification and temporarily improved bearing capacity, while increased cycle counts caused soil degradation and reduced ultimate capacity-evidenced by an 8.4% decrease (from 1.19 kN to 1.09 kN) after 700 cycles under a 13 s period, with degradation rates spanning 8.4-11.2% across frequencies. Deeper embedment depths significantly decreased the maximum bending moment (by similar to 50%) and lateral displacement, highlighting their critical role in optimizing performance. These findings directly inform the design of marine structures by optimizing embedment depth and load frequency to mitigate cyclic degradation, ensuring the long-term serviceability of FRP composite piles in corrosive, high-cycle marine environments.

In general, pile foundations are utilized to support structures like tall buildings, bridges, and transmission towers, which are frequently subjected to lateral stresses initiated by wind, action of waves, earthquakes, or traffic loads. Several high-rise structures, highway and railroad overpasses, as well as transmission towers, are constructed near slopes and rely on pile foundations for support. Due to the effects of wind and waves, pile foundations are continuously subjected to cyclic loads. For piles supporting tall buildings, transmission towers, offshore structures, or infrastructure in seismic zones, 1-way or 2-way cyclic lateral loads are commonly applied. Therefore, while designing pile foundations, it is essential to understand how piles behave laterally when they are located near a sloping crest. One of the primary challenges in ensuring the efficient functioning of the superstructure is analyzing how the soil and foundations respond when exposed to long-term lateral loads, such as wind, over an extended period on the piles of offshore platforms. Because of the presence of slope, the pile's lateral load capacity decreased due to the reduced ability of the soil to provide passive resistance. This paper presents small-scale 1-g model tests conducted on the sand to assess the loss of pile's lateral capacity when subjected to 100 cycles under 1 and 2-way cyclic loading. The Relative Density (60%) and varying slopes (Horizontal ground, 1V:3H) with varying spacing (5D and 7D) and aspect ratios (L/D) of 25 and 40 were implemented in this study. Cyclic lateral load tests were performed for sloping as well as horizontal ground. A major reduction in lateral capacity, exceeding 60%, was observed due to the application of cyclic loading. Moreover, the transition from horizontal ground (HG) to sloping ground (SG) decreased the maximum bending moment by 25-40%. This study exemplifies the piles' behaviour when subjected to cyclic lateral loading while resting on a sloping crest, which represents a critical scenario in pile foundation design.

Monopile foundations of offshore wind turbines embedded in soft clay are subjected to the long-term cyclic lateral loads induced by winds, currents, and waves, the vibration of monopile leads to the accumulation of pore pressure and cyclic strains in the soil in its vicinity, which poses a threat to the safety operation of monopile. The researchers mainly focused on the hysteretic stress-strain relationship of soft clay and kinds of stiffness degradation models have been adopted, which may consume considerable computing resources and is not applicable for the long-term bearing performance analysis of monopile. In this study, a modified cyclic stiffness degradation model considering the effect of plastic strain and pore pressure change has been proposed and validated by comparing with the triaxial test results. Subsequently, the effects of cyclic load ratio, pile aspect ratio, number of load cycles, and length to embedded depth ratio on the accumulated rotation angle and pore pressure are presented. The results indicate the number of load cycles can significantly affect the accumulated rotation angle of monopile, whereas the accumulated pore pressure distribution along the pile merely changes with pile diameter, embedded length, and the number of load cycles, the stiffness of monopile can be significantly weakened by decreasing the embedded depth ratio L/H of monopile. The stiffness degradation of soil is more significant in the passive earth pressure zone, in which soil liquefaction is likely to occur. Furthermore, the suitability of the accumulated rotation angle and accumulated pore pressure design criteria for determining the required cyclic load ratio are discussed.