The application of disposable face mask fibers in the enhancement of the mechanical properties of cement-stabilized soils is rigorously examined in this study through performing several triaxial tests on fiber-reinforced sand-cement mixtures with varying contents of additives under different confining pressures. To this end, sand samples stabilized with different percentages of cement (4% and 8%) are reinforced with various contents of face mask fibers (0%, 0.25%, 0.5% and 0.75%). After seven days of curing, the fiber-reinforced stabilized specimens are subjected to a comprehensive series of consolidated drained (CD) triaxial tests with all-round pressures of 50, 100 and 200 kPa. The results generally show that the addition of mask fibers to sand-cement mixtures up to 0.25% increases their ultimate strengths; whereas further increase of fiber content is observed to have an adverse impact on the strength parameters of the composite. Therefore, 0.25% mask fiber inclusion is reported to be the optimum content, which constitutes maximum strength characteristics of the samples. The contribution of mask fiber addition to the variation of ultimate strength of stabilized mixtures is noticed to be more pronounced in the samples with higher cement contents under greater isotropic confining pressures. Moreover, with increasing the percentage of mask fibers, the failure strain of all stabilized samples increases, thus exhibiting more ductile behavior. Unlike for the samples containing relatively low cement contents (4% herein) where brittleness index is barely affected by the mask fiber content, this parameter significantly decreases with the fiber inclusion for the specimens stabilized with relatively high cement contents (8% herein). Secant modulus is also observed to experience a decreasing trend with the addition of mask fibers to the mixture; the trend which is more pronounced for samples containing higher cement contents. Finally, the internal friction angle and cohesion of cement-stabilized samples generally show increasing trends with the addition of mask fibers up to 0.25% and then reveal decrement. Overall, the combination of cementation and fiber reinforcement demonstrates a significant synergistic effect, resulting in notable improvements in the mechanical properties of fine sands.

Background: The current focus is largely on whole course medical management of coronavirus disease-19 (COVID-19) with real-time polymerase chain reaction (RT-PCR) and radiological features, while the mild cases are usually missed. Thus, combination of multiple diagnostic methods is urgent to understand COVID-19 fully and to monitor the progression of COVID-19. Methods: laboratory variables of 40 mild COVID-19 patients, 30 patients with community-acquired pneumonia (CAP) and 32 healthy individuals were analyzed by principal component analysis (PCA), Kruskal test, Procrustes test, the vegan package in R, CCA package and receiver operating characteristic to investigate the characteristics of the laboratory variables and their relationships in COVID-19. Results: The correlations between the laboratory variables presented a variety of intricate linkages in the COVID-19 group compared with the healthy group and CAP patient group. The prediction probability of the combination of lymphocyte count (LY), eosinophil (EO) and platelets (PLT) was 0.847, 0.854 for the combination of lactate (LDH), creatine kinase isoenzyme (CK-MB), and C-reactive protein (CRP), 0.740 for the combination of EO, white blood cell count (WBC) and neutrophil count (NEUT) and 0.872 for the combination of CK-MB and P. Conclusions: The correlations between the laboratory variables in the COVID-19 group could be a unique characteristic showing promise as a method for COVID-19 prediction and monitoring progression of COVID-19 infection.

A comprehensive global investigation on the impact of reduction (changes) in aerosol emissions due to Coronavirus disease-2019 (COVID-19) lockdowns on aerosol single scattering albedo (SSA) utilizing satellite observations and model simulations is conducted for the first time. The absolute change in Ozone Monitoring Instrument (OMI) retrieved, and two highly-spatially resolved models (Modern-Era Retrospective Analysis for Research and Applications-2 (MERRA-2) and Copernicus Atmosphere Monitoring Service (CAMS)) simulated SSA is <4% (<0.04-0.05) globally during COVID (2020) compared to normal (2015-2019) period. Change in SSA during COVID is not significantly different from long-term and year-to-year variability in SSA. A small change in SSA indicates that significant reduction in anthropogenic aerosol emissions during COVID-19 induced lockdowns has a negligible effect in changing the net contribution of aerosol scattering and/or absorption to total aerosol extinction. The changes in species-wise aerosol optical depth (AOD) are examined in detail to explain the observed changes in SSA. Model simulations show that total AOD decreased during COVID-19 lockdowns, consistent with satellite observations. The respective contributions of sulfate and black carbon (BC) to total AOD increased, which resulted in a negligible change in SSA during the spring and summer seasons of COVID over South Asia. Europe and North America experience a small increase in SSA (<2%) during the summer season of COVID due to a decrease in BC contribution. The change in SSA (2%) is the same for a small change in BC AOD contribution (3%), and for a significant change in sulfate AOD contribution (20%) to total AOD. Since, BC SSA is 5-times lower (higher absorption) than that of sulfate SSA, the change in SSA remains the same. For a significant change in SSA to occur, the BC AOD contribution needs to be changed significantly (4-5 times) compared to other aerosol species. A sensitivity analysis reveals that change in aerosol radiative forcing during COVID is primarily dependent on change in AOD rather than SSA. These quantitative findings can be useful to devise more suitable future global and regional mitigation strategies aimed at regulating aerosol emissions to reduce environmental impacts, air pollution, and public health risks.

Immuno-compromised COVID-19 patients being treated with glucocorticoids like Dexamethasone for prolonged periods had led to the surge of mucormycosis. Mucor spores proliferate and spread faster in COVID afflicted persons. In India, more than 51,775 cases and 4300 deaths due to COVID-associated mucormycosis were reported till date. The Government of J&K declared an epidemic of COVID-19 associated mucormycosis under Sect. 2 of the Epidemic Disease Act, 1897. In the backdrop of current COVID scenario, it becomes imperative to study the etiological factors, occurrence of causative agents and aerosolisation of the Mucor spores from the environmental samples leading to mucormycosis. The present study was undertaken to check the presence of Mucor spores in the environment so as to find the reinforcing sources of COVID associated mucormycosis. We isolated three strains of Mucor species: Mucor circinelloides and two Mucor hiemalis species, from environmental samples (air, soil and water), all having a positive relevance to mucormycosis. This is the first study on the presence of mucormycosis causing Mucor species in Kashmir environment. In this study, some pathogenicity marker tests were performed to detect the virulence of these fungal strains such as Anti-fungal susceptibility test (AST), biofilm formation and heat stress test. The in vitro antifungal susceptibility of these species showed the major zone of inhibition by Amphotericin B (Amph) and Nystatin (NS), whereas, Fluconazole (FLC) showed no activity. Biofilm was formed by both Mucor species which was confirmed by crystal violet assay (CV) with positive absorbance readings in microplate reader. Under heat stress, pathogenicity marker test was performed in which both species formed considerable aseptate hyphal growth and small scattered spores. During SEM (Scanning Electron Microscopy) analysis, both the species of Mucor were observed with intact sporangia producing several sporangiospores, whose size dimorphism is linked to its virulence. Thus, augmented knowledge of the epidemiology and clinical presentations of these Mucor species may prevent environmental exposure of immune-compromised patients post-COVID and improve early diagnosis and treatment.

The COVID-19 pandemic caused unprecedented damage to humanity, and while vaccines have been developed, they are not fully effective against the SARS-CoV-2 virus. Limited targeted drugs, such as Remdesivir and Paxlovid, are available against the virus. Hence, there is an urgent need to explore and develop new drugs to combat COVID-19. This study focuses on exploring microbial natural products from soil-isolated bacteria Streptomyces sp. strain 196 and RI.24 as a potential source of new targeted drugs against SARS-CoV-2. Molecular docking studies were performed on holoRdRp and nsp13, two key factors responsible for virus replication factor. Our in silico studies, K-252-C aglycone indolocarbazole alkaloid (K252C) and daunorubicin were found to have better binding affinities than the respective control drugs, with K252C exhibiting binding energy of - 9.1 kcal/mol with holoRdRp and - 9.2 kcal/mol with nsp13, and daunorubicin showing binding energy at - 8.1 kcal/mol with holoRdRp and - 9.3 kcal/mol with nsp13. ADMET analysis, MD simulation, and MM/GBSA studies indicated that K252C and daunorubicin have the potential to be developed as targeted drugs against SARS-CoV-2. The study concludes that K252C and daunorubicin are potential lead compounds that might suppress the inhibition of SARS-CoV-2 replication among the tested microbial compounds and could be developed as targeted drugs against COVID-19. In the future, further in vitro studies are required to validate these findings. [GRAPHICS]

In this study, we evaluated the variations of air quality in Lanzhou, a typical city in Northwestern China impacted by the COVID-19 lockdown. The mass concentration and chemical composition of non-refractory submicron particulate matter (NR-PM1) were determined by a high-resolution aerosol mass spectrometer during January-March 2020. The concentration of NR-PM(1)dropped by 50% from before to during control period. The five aerosol components (sulfate, nitrate, ammonium, chloride, and organic aerosol [OA]) all decreased during the control period with the biggest decrease observed for secondary inorganic species (70% of the total reduction). Though the mass concentration of OA decreased during the control period, its source emissions varied differently. OA from coal and biomass burning remained stable from before to during control period, while traffic and cooking related emissions were reduced by 25% and 50%, respectively. The low concentration during the control period was attributed to the lower production rate for secondary aerosols.

The Tibetan Plateau holds the largest mass of snow and ice outside of the polar regions. The deposition of light-absorbing particles (LAPs) including mineral dust, black carbon and organic carbon and the resulting positive radiative forcing on snow (RFSLAPs) substantially contributes to glacier retreat. Yet how anthropogenic pollutant emissions affect Himalayan RFSLAPs through transboundary transport is currently not well known. The COVID-19 lockdown, resulting in a dramatic decline in human activities, offers a unique test to understand the transboundary mechanisms of RFSLAPs. This study employs multiple satellite data from the moderate resolution imaging spectroradiometer and ozone monitoring instrument, as well as a coupled atmosphere-chemistry-snow model, to reveal the high spatial heterogeneities in anthropogenic emissions-induced RFSLAPs across the Himalaya during the Indian lockdown in 2020. Our results show that the reduced anthropogenic pollutant emissions during the Indian lockdown were responsible for 71.6% of the reduction in RFSLAPs on the Himalaya in April 2020 compared to the same period in 2019. The contributions of the Indian lockdown-induced human emission reduction to the RFSLAPs decrease in the western, central, and eastern Himalayas were 46.8%, 81.1%, and 110.5%, respectively. The reduced RFSLAPs might have led to 27 Mt reduction in ice and snow melt over the Himalaya in April 2020. Our findings allude to the potential for mitigating rapid glacial threats by reducing anthropogenic pollutant emissions from economic activities.

Coronavirus disease (COVID-19) has disrupted health, economy, and society globally. Thus, many countries, including China, have adopted lockdowns to prevent the epidemic, which has limited human activities while affecting air quality. These affects have received attention from academics, but very few studies have focused on western China, with a lack of comparative studies across lockdown periods. Accordingly, this study examines the effects of lockdowns on air quality and pollution, using the hourly and daily air monitoring data collected from Lanzhou, a large city in Northwest China. The results indicate an overall improvement in air quality during the three lockdowns compared to the average air quality in the recent years, as well as reduced PM2.5, PM10, SO2, NO2, and CO concentrations with different rates and increased O3 concentration. During lockdowns, Lanzhou's morning peak of air pollution was alleviated, while the spatial characteristics remained unchanged. Further, ordered multi-classification logistic regression models to explore the mechanisms by which socioeconomic backgrounds and epidemic circumstances influence air quality revealed that the increment in population density significantly aggravated air pollution, while the presence of new cases in Lanzhou, and medium- and high-risk areas in the given district or county both increase the likelihood of air quality improvement in different degrees. These findings contribute to the understanding of the impact of lockdown on air quality, and propose policy suggestions to control air pollution and achieve green development in the post-epidemic era.

The unprecedented COVID-19 outbreak impacted the world in many aspects. Air pollutants were largely reduced in cities worldwide in 2020. Using samples from two snow pits dug separately in 2019 and 2020 in Urumqi Glacier No. 1 (UG1) in the Xinjiang Uygur Autonomous Region (Xinjiang), China, we measured water-stable isotopes, soluble ions, and black and organic carbon (BC and OC). Both carbon types show no significant variations in the snow-pit profiles dated from 2018 through 2020. The deposition of anthropogenically induced soluble ions (K+, Cl-, SO42-, and NO3-) in the snow decreased to 20-40% of their respective concentrations between 2019 and 2020; however, they increased 2- to fourfold from 2018 to 2019. We studied the daily concentrations of SO2 (2019-2020), NO2 (2015-2020), CO (2019-2020), and PM2.5 (2019-2020) measured in the sixteen major cities and towns across Xinjiang. The variabilities in these air pollutants were supposed to illustrate the air quality in the urban area and represent the change in the source area. The NO2 decreased in response to mobility restrictions imposed by local governments, while SO2, CO, and PM2.5 did not consistently correspond. This difference indicates that the restriction measures primarily affected traffic. The increases in chemical species in the snow from 2018 to 2019 and the subsequent decreases from 2019 to 2020 were consistent with the variations in SO2 and NO2 measured in urban air and estimated by MERRA-2 model. Therefore, the pandemic could possibly have an impact on snow chemistry of the Tien-Shan glaciers via reduced traffic and industrial intensity; more evidence would be obtained from ice cores, tree rings, and other archives in the future.

A nationwide lockdown was imposed in India due to the Coronavirus Disease 2019 (COVID-19) pandemic which significantly reduced the anthropogenic emissions. We examined the characteristics of equivalent black carbon (eBC) mass concentration and its source apportionment using a multiwavelength aethalometer over an urban site (Ahmedabad) in India during the pandemic induced lockdown period of year 2020. For the first time, we estimate the changes in BC, its contribution from fossil (eBC(ff)) and wood (eBC(wf)) fuels during lockdown (LD) and unlock (UL) periods in 2020 with respect to 2017 to 2019 (normal period). The eBC mass concentration continuously decreased throughout lockdown periods (LD1 to LD4) due to enforced and stringent restrictions which substantially reduced the anthropogenic emissions. The eBC mass concentration increased gradually during unlock phases (UL1 to UL7) due to the phase wise relaxations after lockdown. During lockdown period eBC mass concentration decreased by 35%, whereas during the unlock period eBC decreased by 30% as compared to normal period. The eBC(wf) concentrations were higher by 40% during lockdown period than normal period due to significant increase in the biomass burning emissions from the several community kitchens which were operational in the city during the lockdown period. The average contributions of eBC(ff) and eBC(wf) to total eBC mass concentrations were 70% and 30% respectively during lockdown (LD1 to LD4) period, whereas these values were 87% and 13% respectively during the normal period. The reductions in BC concentrations were commensurate with the reductions in emissions from transportation and industrial activities. The aerosol radiative forcing reduced significantly due to the reduction in anthropogenic emissions associated with COVID-19 pandemic induced lockdown leading to a cooling of the atmosphere. The findings in the present study on eBC obtained during the unprecedented COVID-19 induced lockdown can provide a comprehensive understanding of the BC sources and current emission control strategies, and thus can serve as baseline anthropogenic emissions scenario for future emission control strategies aimed to improve air quality and climate.